Page 1 of 2 • 1, 2
Calculating the Voltage
on Wed Aug 29, 2018 2:51 pm
The Voltage
Voltage is the pressure from an electrical circuit's power source that pushes charged electrons (current) through a conducting loop, enabling them to do work such as illuminating a light.
In Ohm's Law Voltage is represented in letter "V" and measured in volt.
The Voltage is directly proportional to the Resistance and Current.
In Mathematical Equation
V= I*R
Where:
V= Voltage
I= Current
R= Resistance
in the good example of Ohm's Law is the water tank where the Water flow is the Current, the size of the water pipe is the Resistance and the Voltage is the pressure that push the water.
The higher the current the higher the voltage
Example in Calculating the Voltage
1. Calculate the amount of the Voltage for 0.007 A through 5000 Ω.
Given:
I= 0.007 A
R= 5000 Ω
V= ?
Solution:
V= IR
V= 0.007 A* 5000 Ω
V= 35 V
Voltage is the pressure from an electrical circuit's power source that pushes charged electrons (current) through a conducting loop, enabling them to do work such as illuminating a light.
In Ohm's Law Voltage is represented in letter "V" and measured in volt.
The Voltage is directly proportional to the Resistance and Current.
In Mathematical Equation
V= I*R
Where:
V= Voltage
I= Current
R= Resistance
in the good example of Ohm's Law is the water tank where the Water flow is the Current, the size of the water pipe is the Resistance and the Voltage is the pressure that push the water.
The higher the current the higher the voltage
Example in Calculating the Voltage
1. Calculate the amount of the Voltage for 0.007 A through 5000 Ω.
Given:
I= 0.007 A
R= 5000 Ω
V= ?
Solution:
V= IR
V= 0.007 A* 5000 Ω
V= 35 V
Re: Calculating the Voltage
on Tue Sep 04, 2018 12:31 pm
is it important to know if it's a high or a low voltage?
Re: Calculating the Voltage
on Wed Sep 05, 2018 1:29 pm
nyella wrote:how does the voltage affects the circuit?
Current is the flow of electricity in a circuit and is measured in amps, resistance which is measured in ohms, is the thing that slows current down in a circuit. Ohm's Law is that more voltage creates more current and more resistance creates less current.
Re: Calculating the Voltage
on Wed Sep 05, 2018 1:36 pm
nyella wrote:is it important to know if it's a high or a low voltage?
Yes, because it can cause premature failure of electrical and electronic components in circuit boards due to overheating like for example if the voltage was too high, there is a point where the voltage level supplied can be so high as to damage a motor but this level is far higher than that for electronics while if the voltage was too low , there is a tendency that it can't supply the right amount of voltage that it needed for a component to be able to use.
Re: Calculating the Voltage
on Fri Sep 07, 2018 7:42 am
kc wrote:nyella wrote:is it important to know if it's a high or a low voltage?
Yes, because it can cause premature failure of electrical and electronic components in circuit boards due to overheating like for example if the voltage was too high, there is a point where the voltage level supplied can be so high as to damage a motor but this level is far higher than that for electronics while if the voltage was too low , there is a tendency that it can't supply the right amount of voltage that it needed for a component to be able to use.
There is a big difference between how high the voltage and how low it is. It may affect a lot with the circuit if you connect a high voltage even if its only need to have a low voltage. We should always check the voltage before we connect it to the circuit.
Re: Calculating the Voltage
on Fri Sep 07, 2018 7:43 am
kc wrote:What causes under voltage?
Undervoltage conditions are usually be caused by undersized or overloaded utility and facility transformers.
Re: Calculating the Voltage
on Fri Sep 07, 2018 7:45 am
kc wrote:Does low voltage mean low hazard?
lowvoltage cabling—such as telecommunications, security or video—is not strong enough to cause a fatal electric shock. The bad news is there still are very real safety risks when performing lowvoltage installations.
Re: Calculating the Voltage
on Fri Sep 07, 2018 8:17 am
Why do we say V=IR, why don't we say VR=I, because if V is directly proportional to I, then I is directly proportional to V and can't we write then I=VR?
Re: Calculating the Voltage
on Fri Sep 07, 2018 8:23 am
What's the difference between voltage and electromotive force?
Re: Calculating the Voltage
on Fri Sep 07, 2018 8:39 am
White wrote:Can electrons move at the speed of light ?
A calculation shows that the electron is traveling at about 2,200 kilometers per second. That's less than 1% of the speed of light, but it's fast enough to get it around the Earth in just over 18 seconds
Re: Calculating the Voltage
on Fri Sep 07, 2018 8:43 am
White wrote:What's the difference between voltage and electromotive force?
EMF stands for electromotive force and is a measure of the difference of electrical potential between two points. The strength of an electromotive force is measured in the unit "Volts"
Re: Calculating the Voltage
on Fri Sep 07, 2018 8:55 am
If the voltage across a fixed value of resistance is increased five times, what does the current do?
Re: Calculating the Voltage
on Fri Sep 07, 2018 9:08 am
nyella wrote:how does the voltage affects the circuit?
voltage has a very important role on electricity, if there is no voltage, there is no electricity at all.
Re: Calculating the Voltage
on Fri Sep 07, 2018 9:31 am
The current is five times ding mag iincrease, beacause if the voltage increases the current also increases.White wrote:
If the voltage across a fixed value of resistance is increased five times, what does the current do?
Re: Calculating the Voltage
on Fri Sep 07, 2018 9:32 am
White wrote:Why do we say V=IR, why don't we say VR=I, because if V is directly proportional to I, then I is directly proportional to V and can't we write then I=VR?
I think okay naman yung formula na yan haha
Re: Calculating the Voltage
on Fri Sep 07, 2018 9:35 am
nyella wrote:how does the voltage affects the circuit?
Yung voltage kase siya yung nag pupush ng current to flow over the circuit so kapag wala yung voltage how can a current move?
Re: Calculating the Voltage
on Tue Sep 11, 2018 9:04 am
White wrote:Why do we say V=IR, why don't we say VR=I, because if V is directly proportional to I, then I is directly proportional to V and can't we write then I=VR?
We're looking for the voltage. If you use I = VR , it means you're looking for I, there is an appropriate and right formula for I. VR = I means your looking for VR. VR doesn't stand for anything so why look for it.
Re: Calculating the Voltage
on Tue Sep 11, 2018 9:08 am
Does voltage have different effects in a series and parallel circuit?
Re: Calculating the Voltage
on Tue Sep 11, 2018 9:10 am
Because voltage is directly proportional to current.Admin wrote:The current is five times ding mag iincrease, because if the voltage increases the current also increases.White wrote:
If the voltage across a fixed value of resistance is increased five times, what does the current do?
Re: Calculating the Voltage
on Tue Sep 11, 2018 12:53 pm
DRAVEN wrote:nyella wrote:how does the voltage affects the circuit?
voltage has a very important role on electricity, if there is no voltage, there is no electricity at all.
Voltage is very important because it pushes the current so that it can flow.
Re: Calculating the Voltage
on Sat Sep 15, 2018 1:14 am
Pinkeroo wrote:Does voltage have different effects in a series and parallel circuit?
Well maybe it differs only dun sa amount nang voltage na ginamit dun sa parallel and series.. ibig sabihin it can affect a parallel and a series if the amont of voltage is higher or lower.
Page 1 of 2 • 1, 2
Permissions in this forum:
You cannot reply to topics in this forum

